![obd2 reader altima obd2 reader altima](https://m.media-amazon.com/images/I/61cTFoxqEBL.jpg)
- Obd2 reader altima how to#
- Obd2 reader altima serial#
- Obd2 reader altima driver#
- Obd2 reader altima registration#
Old PCM is roasted, see attached picture when attempts are made to communicate after fixing the wiring problem An open ground or power (B+) circuit on a fuel-injected engine removes power from the ECM and prevents the engine from starting. PCM receives battery voltage (B+) through a fuse or fusible link. With the ignition key ON and bus activity, the voltage should vary from 0 to 5V depending on the amount of bus activity! With the ignition key ON and no bus activity, This tests the ECM Voltage supply as no power may be caused by a blown lighter fuseĬonnect positive DMM lead to either DLC bias terminalsĬonnect negative DMM lead to the ground terminal
Obd2 reader altima serial#
With the Ignition on, voltage on the class 2 serial data pin should be 5V or fluctuating between 3.5V and 5.0V, If open, PCM cannot transmit data to the scan toolĬonnect positive DMM lead to DLC Battery + terminalĬonnect negative DMM lead to battery ground terminal
![obd2 reader altima obd2 reader altima](https://m.media-amazon.com/images/I/51uQmT81DhL.jpg)
NOTE: An open circuit or high ground resistance means that the PCM will never enter diagnostic mode.Ĭonnect the positive DMM lead to the class 2 Serial Data pin and the negative DMM lead to either pin 4 or pin 5 or a known good ground With the ignition on, voltage drop across the ground terminal should be 0.1 Volts or less Do not connect to body or chassis ground but to the battery terminal directly If you’re a locksmith, simply buy IM508 plus XP400 Pro separately will be a good investment.If the scan tool does not receive data from an OBD II vehicleĬonnect the positive DMM lead to DLC pin 4 and the negative DMM lead to the negative battery terminal, using jumper wires if necessary.
Obd2 reader altima how to#
This is how to use Autel IM508 to program 2 keys for 2020 Nissan Altima SL when all keys lost. Press the start button, within 5s to put the key mark of the first programmed smart key close to start button, the buzzer rings continuously, turn off ignition.Ĭheck if the remote control is operating properly. Press “Yes” to program next one, “No” to complete. Transferred data can then be displayed, saved. The standard SAE J1962 specifies two female OBD2 16-pin. The OBD2 connector lets you access data from your car easily. This lets him read OBD2 codes aka Diagnostic Trouble Codes (DTCs) to review and troubleshoot the issue. Note: if the indicator light doesn’t go out, please use a working key to press the start button. OBD2 TekLink is a software application the lets you transfer Diagnostic Data from your OBD2 Code Reader to a PC. To do so, he will connect the OBD2 reader to the OBD2 16 pin connector near the steering wheel. Press start button once, keep the logo side of a new smart key cling to car start button, then the dashboard is illuminated and the indicator light flashes 5 times. Under left (drivers) side dash - same place ALL of em are located. Just need to locate my OBD II port location. Turn off the ignition and turn on the emergency flasher. Asked by Suzie1951 in Summerfield, FL on April 30, 2020. Note down BCM code, press “Yes” to continue. Perform this function will delete all the smart keys, it can program up to 4 smart keys!Ĭlose all the doors and click the start button.
Obd2 reader altima registration#
Immo/ smart system > Smart key > Immobilizer remote control learning > When performing key registration Wait for scanning vehicle system until 100%…
![obd2 reader altima obd2 reader altima](https://i.ytimg.com/vi/Y-I7GE2t3xE/hqdefault.jpg)
Obd2 reader altima driver#
Please open and close the driver door once. Please illuminate the instrument cluster before the operation(if the ignition can be turned on)! How to program 2020 Nissan Altima SL all keys lost?Ĭonnect Autel IM508 Key Programmer with OBD, press Detailed vehicle list as below:Īutel IM508 IMMO Nissan(NA) Altima Car List YearīCM(partially support), ECM(partially support) Doesn't work with Fiat, 2003 Ford Ranger, 2000 Sarum, 2000 Honda Civic, 2001 Altima, 2002 Dodge Neon, 2002 Acura, 2003 GMC, 2003 Ford,2005 Toyota Vitz, Renault clio 2005. IMMO supported add key, all keys lost, read password & remote learning. Bluetooth OBD-II Scanner for OBD2, EOBD cars: Can work on gasoline vehicle that is 1996 or newer with standard OBDII(16-pin DLC). Autel MaxiIM IM508 can program 2020 Nissan Altima SL AKL(all keys lost)by OBD Success.